How to Change a Brake Caliper
Gather the proper tools need to replace brake calipers., Loosen the lug nuts on the wheel for the caliper you'll be replacing.Don't loosen the nuts completely; about half a turn should do it., Use a jack to carefully lift your car off the ground...
Step-by-Step Guide
-
Step 1: Gather the proper tools need to replace brake calipers.
You won't need a lot, and any tools you don't have can usually be rented at an auto supply shop in your town, so don't go out and buy these until you know you need them:
Socket set Brake line wrench Drop light Screwdrivers Needlenose pliers Torque Wrench Gloves and goggles Brake fluid Car jack Service manual -
Step 2: Loosen the lug nuts on the wheel for the caliper you'll be replacing.Don't loosen the nuts completely; about half a turn should do it.
, Ensure the jack is positioned correctly in a safe position under your car, then add jack stands and wheel blocks to keep the car secure.
Never work under a car with just the hydraulic jack.It is not strong or stable enough.
Refer to your owner's manual for lifting points if you are unsure where to place the jack. , Turn the wheel to the proper position to where the caliper may be accessed easily. ,, Remove the retaining bolts that hold the caliper's brake hose in place to allow movement with a wrench.
Some cars may have clips in place of the bolts.
Use the edge of a Phillips or flathead screwdriver to pry open the clips.
Throw away the old brass or copper washers.
Never reuse old washers. , Never clamp or crimp a brake line, as it can be damaged and this would result in brake failure, possibly causing an accident or worse., The fitting shown is also known as a "banjo" fitting. , Some vehicles have 2 bolts, while others may only have one to take out. , Carefully remove the brake pads from the caliper.
Try to avoid dropping brake pads as it can cause serious damage. , If there is any corrosion or interference be sure to remove before new caliper installation. , Place the brake pads into the new caliper if they are not preloaded.
Do not apply grease to the side of the brake pad that is in contact with the rotor. , Install new mounting bolts (if supplied) if not reuse the bolts you removed and tighten to your vehicle's specifications.
You might need a torque wrench to do this.
Be sure not to over tourque. , Torque to your vehicle specifications. ,, Refill with proper DOT specification for you vehicle, any brake fluid that was lost. , Snug the lug nuts in a star formation.
Carefully lower your vehicle back onto the ground.
Refer to the owner's manual for the final torque value and tighten with a torque wrench only after the tires are back on the ground.
The use of an impact wrench by an untrained person isn't recommended. , if brakes don't feel like they are working properly, contact a certified technician immediately. -
Step 3: Use a jack to carefully lift your car off the ground
-
Step 4: then support it with jack stands and wheel blocks.
-
Step 5: Remove the lug nuts or bolts completely from studs and remove the front tires.
-
Step 6: Compress the caliper piston completely into the bore with a C-clamp or piston retracting tool.
-
Step 7: Be sure to have an oil pan to catch any excess brake fluid.
-
Step 8: Insert a small rubber plug into the hose or use a bolt
-
Step 9: 2 washers and a nut on Banjo fittings to minimize fluid loss and contaminants from entering the system.
-
Step 10: Loosen and remove the caliper fitting with a wrench.
-
Step 11: Remove the caliper mounting bolts with a wrench
-
Step 12: be sure to save these bolts as you may need to reuse them.
-
Step 13: Lift the caliper up until it clears the rotor and then slide it off.
-
Step 14: Inspect the caliper supports for rusting or corrosion that would interfere with the new caliper.
-
Step 15: If provided or recommended by the manufacturer
-
Step 16: lubricate the BACK of the brake pads
-
Step 17: mounting bushings and sleeves with the recommended grease.
-
Step 18: Carefully slide the brake pad and caliper assembly over the rotor.
-
Step 19: Reconnect the caliper hose with the caliper (banjo) fitting and new washers.
-
Step 20: Remove the plug from the hose and use a wrench or torque wrench to replace the retaining bolts or clips.
-
Step 21: Bleed your brakes until they are firm.
-
Step 22: Put the wheels back onto your car.
-
Step 23: Test the feel of your car's brakes before you travel.
Detailed Guide
You won't need a lot, and any tools you don't have can usually be rented at an auto supply shop in your town, so don't go out and buy these until you know you need them:
Socket set Brake line wrench Drop light Screwdrivers Needlenose pliers Torque Wrench Gloves and goggles Brake fluid Car jack Service manual
, Ensure the jack is positioned correctly in a safe position under your car, then add jack stands and wheel blocks to keep the car secure.
Never work under a car with just the hydraulic jack.It is not strong or stable enough.
Refer to your owner's manual for lifting points if you are unsure where to place the jack. , Turn the wheel to the proper position to where the caliper may be accessed easily. ,, Remove the retaining bolts that hold the caliper's brake hose in place to allow movement with a wrench.
Some cars may have clips in place of the bolts.
Use the edge of a Phillips or flathead screwdriver to pry open the clips.
Throw away the old brass or copper washers.
Never reuse old washers. , Never clamp or crimp a brake line, as it can be damaged and this would result in brake failure, possibly causing an accident or worse., The fitting shown is also known as a "banjo" fitting. , Some vehicles have 2 bolts, while others may only have one to take out. , Carefully remove the brake pads from the caliper.
Try to avoid dropping brake pads as it can cause serious damage. , If there is any corrosion or interference be sure to remove before new caliper installation. , Place the brake pads into the new caliper if they are not preloaded.
Do not apply grease to the side of the brake pad that is in contact with the rotor. , Install new mounting bolts (if supplied) if not reuse the bolts you removed and tighten to your vehicle's specifications.
You might need a torque wrench to do this.
Be sure not to over tourque. , Torque to your vehicle specifications. ,, Refill with proper DOT specification for you vehicle, any brake fluid that was lost. , Snug the lug nuts in a star formation.
Carefully lower your vehicle back onto the ground.
Refer to the owner's manual for the final torque value and tighten with a torque wrench only after the tires are back on the ground.
The use of an impact wrench by an untrained person isn't recommended. , if brakes don't feel like they are working properly, contact a certified technician immediately.
About the Author
Theresa Phillips
Experienced content creator specializing in crafts guides and tutorials.
Rate This Guide
How helpful was this guide? Click to rate: