How to Fix a Scratched Video Game Disk with White Toothpaste
Inspect the scratches., Dampen a soft, lint-free cloth., Wipe the reflective side of the disk., Dry the disk carefully., Choose the toothpaste., Apply a small amount of toothpaste to the polishing cloth., Gently rub the toothpaste over the disk...
Step-by-Step Guide
-
Step 1: Inspect the scratches.
Toothpaste works best for shallow scratches and scuffs on the reflective side.It will probably not work on a deep scratch.
Scratches on the non-reflective label side should never be rubbed, and may have caused irreparable damage.
If you have deep scratches, consider sending the disk to a disk repair service.
You could also try more abrasive treatments, such as a non-petroleum-based metal polish. -
Step 2: Dampen a soft
Lightly dampen a cotton or microfiber cloth.
You'll use this to clean grime off the disk.
If you skip this section, the toothpaste could rub dirt particles into the CD, making the scratch worse.
Avoid any rough or dusty materials.
If the disk is visibly greasy or dirty, wipe it under running water. , Gently brush the wet cloth against the disk.
Wipe each stroke outwards from the center, like a spoke on a bicycle wheel.
Rubbing in circles increases the risk of damage.
Hold the disk by the rim to avoid adding additional dirt and oil from your fingers. , A dry cloth is more likely to damage the disk.
One of these methods of drying are recommended instead:
Place face down on a couple layers of paper towel and wait until dry.
Loosely wad a paper towel and brush from the center outward.
Do not push onto the disk; the only pressure should come from the bending of the paper towel.Let air dry. , You must use actual paste, not a gel toothpaste.
The paste contains abrasive material that scrapes plaque off your teeth.
This will sand down the scratched surface as well, hiding the scratch causing the laser to misread.Baking soda toothpaste works well due to the extra grit.
If you're lucky, your toothpaste will list an abrasion rating, called RDA.No one's tested how RDA affects disk cleaning, but a higher rating (120+) should work better. , A small dab should be enough.
As before, use a clean, lint-free cloth such as cotton or microfiber. , Always move radially, from the center of the disk straight out to the rim.
Do not rub in circular motions.
Continue rubbing gently until the scratch is gone or nearly gone.
This can take a few minutes.
Do not polish harder in an attempt to speed up the process.
This can cause further damage to the disk. , Ensure that you remove all of the toothpaste.
You may need to use a clean polishing cloth to remove residue, using the same wiping pattern. , You may wipe it with a dry cloth, but blotting with a paper towel is safer.
You should notice that scratches are fainter or even completely gone.
You may have made some additional tiny scratches, but provided that you did not press hard, these shouldn’t interfere with the disk. , Place the disk into the appropriate drive and see if it works.
If so, then you are done.
If not, repeat the toothpaste treatment for a second round.
If there is no noticeable improvement at all, try again with a grittier toothpaste, or with petroleum-free metal polish.
If two rounds of polishing do not work, try sending it to a disk repair service.
These can buff out the scratches with a special machine. -
Step 3: lint-free cloth.
-
Step 4: Wipe the reflective side of the disk.
-
Step 5: Dry the disk carefully.
-
Step 6: Choose the toothpaste.
-
Step 7: Apply a small amount of toothpaste to the polishing cloth.
-
Step 8: Gently rub the toothpaste over the disk.
-
Step 9: Wash the disc off with cold water.
-
Step 10: Dry the disk.
-
Step 11: Test the game.
Detailed Guide
Toothpaste works best for shallow scratches and scuffs on the reflective side.It will probably not work on a deep scratch.
Scratches on the non-reflective label side should never be rubbed, and may have caused irreparable damage.
If you have deep scratches, consider sending the disk to a disk repair service.
You could also try more abrasive treatments, such as a non-petroleum-based metal polish.
Lightly dampen a cotton or microfiber cloth.
You'll use this to clean grime off the disk.
If you skip this section, the toothpaste could rub dirt particles into the CD, making the scratch worse.
Avoid any rough or dusty materials.
If the disk is visibly greasy or dirty, wipe it under running water. , Gently brush the wet cloth against the disk.
Wipe each stroke outwards from the center, like a spoke on a bicycle wheel.
Rubbing in circles increases the risk of damage.
Hold the disk by the rim to avoid adding additional dirt and oil from your fingers. , A dry cloth is more likely to damage the disk.
One of these methods of drying are recommended instead:
Place face down on a couple layers of paper towel and wait until dry.
Loosely wad a paper towel and brush from the center outward.
Do not push onto the disk; the only pressure should come from the bending of the paper towel.Let air dry. , You must use actual paste, not a gel toothpaste.
The paste contains abrasive material that scrapes plaque off your teeth.
This will sand down the scratched surface as well, hiding the scratch causing the laser to misread.Baking soda toothpaste works well due to the extra grit.
If you're lucky, your toothpaste will list an abrasion rating, called RDA.No one's tested how RDA affects disk cleaning, but a higher rating (120+) should work better. , A small dab should be enough.
As before, use a clean, lint-free cloth such as cotton or microfiber. , Always move radially, from the center of the disk straight out to the rim.
Do not rub in circular motions.
Continue rubbing gently until the scratch is gone or nearly gone.
This can take a few minutes.
Do not polish harder in an attempt to speed up the process.
This can cause further damage to the disk. , Ensure that you remove all of the toothpaste.
You may need to use a clean polishing cloth to remove residue, using the same wiping pattern. , You may wipe it with a dry cloth, but blotting with a paper towel is safer.
You should notice that scratches are fainter or even completely gone.
You may have made some additional tiny scratches, but provided that you did not press hard, these shouldn’t interfere with the disk. , Place the disk into the appropriate drive and see if it works.
If so, then you are done.
If not, repeat the toothpaste treatment for a second round.
If there is no noticeable improvement at all, try again with a grittier toothpaste, or with petroleum-free metal polish.
If two rounds of polishing do not work, try sending it to a disk repair service.
These can buff out the scratches with a special machine.
About the Author
Jessica Adams
Creates helpful guides on hobbies to inspire and educate readers.
Rate This Guide
How helpful was this guide? Click to rate: