How to Install a Rocketfish TV Mount
Cross reference the Rocketfish TV mount with the TV you own., Remove the stand from the back of the TV., Survey whether the back of your TV is flat or curved., Find the hardware bags labeled M4, M5, M6 and M8., Find the left and right TV brackets...
Step-by-Step Guide
-
Step 1: Cross reference the Rocketfish TV mount with the TV you own.
Each mount has a limit of weight it can support.
For example, with most models your TV must be less than 130 lbs. (59kg). , It will usually slide off or unscrew.
Later, you will use these screw holes to mount the TV., You will attach the TV brackets with different processes depending upon this feature., These are different sized screws and washers, designed to mount to any flat-panel TV.
You should also find a hex key that will install the screws., These are usually labeled B and C and have holes that allow you to install the brackets to many different TVs.
They will run vertically down the back of the TV over the existing screw holes.
Make sure you install the left and right brackets in identical holes, so the TV will fit squarely into the mount. , Test the kits out to see what fits into the screw holes.
Use the hex key to tighten the screws.
The order of installation goes bracket, washer and then screw.
The M4/M5 kit usually includes 12mm screws.
The M6/M8 kit includes 12, 16 or 22mm screws. , Place the spacer above the screw hole on the TV, and then attach a washer, the bracket, another washer and a screw.
Use the hex key to tighten the screws., They are usually included on models that include an arm assembly.
If it does, slide them through the TV brackets horizontally and secure them with 9/16-inch Phillips head screws and a screwdriver., Use an edge-to-edge stud finder for best results.
Choose a stud where you want your TV to be mounted securely.
Use wall anchors if you are installing the TV mount into a concrete wall.
Do not install the Rocketfish mount into drywall.
It must be supported with a stud. ,, Place a level above it and adjust until it is level.
Mark the place where you will screw it in with a pencil.,, Place a washer in front of each hole, followed by a lag bolt.
Tighten the lag bolt into place with a socket wrench.
Be careful not to over tighten the lag bolts or you risk damaging the stud and the TV. , Slide it in from top to bottom, and then attach the cap screws with your hex key., Slide the brackets onto the wall plate until you hear an audible click.
You may need assistance to lift the TV and find the right placement., The arm must fit under the metal tabs.
Secure the arm with bracket screws at the top and bottom., Adjust the angle side to side with an arm assembly model.
You will need to use your hex key to adjust some angles on the arm assembly. -
Step 2: Remove the stand from the back of the TV.
-
Step 3: Survey whether the back of your TV is flat or curved.
-
Step 4: Find the hardware bags labeled M4
-
Step 5: M6 and M8.
-
Step 6: Find the left and right TV brackets.
-
Step 7: Attach the TV brackets to either side of a flat-backed TV using either the M4 and M5 washers and screws or the M6 or M8 washers and screws.
-
Step 8: Attach the TV brackets to either side of a curved TV using spacers that were also included in the M4
-
Step 9: M6 or M8 packs.
-
Step 10: Find whether your TV mount includes horizontal bars.
-
Step 11: Search your wall for studs.
-
Step 12: Hammer a pilot nail into the stud to ensure you have selected a steady location.
-
Step 13: Align your wall plate with the area where you want to mount your TV.
-
Step 14: Drill small pilot holes in these locations with an electric drill.
-
Step 15: Place the wall plate over the holes.
-
Step 16: Insert the arm assembly onto the wall plate if your Rocketfish mount includes one.
-
Step 17: Lift the TV and tilt the top toward the wall if you have a tilting model without arm assembly.
-
Step 18: Alternately
-
Step 19: lift the TV and slide it sideways onto the wall plate if it has arm assembly.
-
Step 20: Adjust the angle up and down on a tilting model.
Detailed Guide
Each mount has a limit of weight it can support.
For example, with most models your TV must be less than 130 lbs. (59kg). , It will usually slide off or unscrew.
Later, you will use these screw holes to mount the TV., You will attach the TV brackets with different processes depending upon this feature., These are different sized screws and washers, designed to mount to any flat-panel TV.
You should also find a hex key that will install the screws., These are usually labeled B and C and have holes that allow you to install the brackets to many different TVs.
They will run vertically down the back of the TV over the existing screw holes.
Make sure you install the left and right brackets in identical holes, so the TV will fit squarely into the mount. , Test the kits out to see what fits into the screw holes.
Use the hex key to tighten the screws.
The order of installation goes bracket, washer and then screw.
The M4/M5 kit usually includes 12mm screws.
The M6/M8 kit includes 12, 16 or 22mm screws. , Place the spacer above the screw hole on the TV, and then attach a washer, the bracket, another washer and a screw.
Use the hex key to tighten the screws., They are usually included on models that include an arm assembly.
If it does, slide them through the TV brackets horizontally and secure them with 9/16-inch Phillips head screws and a screwdriver., Use an edge-to-edge stud finder for best results.
Choose a stud where you want your TV to be mounted securely.
Use wall anchors if you are installing the TV mount into a concrete wall.
Do not install the Rocketfish mount into drywall.
It must be supported with a stud. ,, Place a level above it and adjust until it is level.
Mark the place where you will screw it in with a pencil.,, Place a washer in front of each hole, followed by a lag bolt.
Tighten the lag bolt into place with a socket wrench.
Be careful not to over tighten the lag bolts or you risk damaging the stud and the TV. , Slide it in from top to bottom, and then attach the cap screws with your hex key., Slide the brackets onto the wall plate until you hear an audible click.
You may need assistance to lift the TV and find the right placement., The arm must fit under the metal tabs.
Secure the arm with bracket screws at the top and bottom., Adjust the angle side to side with an arm assembly model.
You will need to use your hex key to adjust some angles on the arm assembly.
About the Author
Beverly Cook
Specializes in breaking down complex lifestyle topics into simple steps.
Rate This Guide
How helpful was this guide? Click to rate: