How to Repair a Fiberglass Tub or Shower
Purchase a suitable kit for your shower (or bathtub)., Clean the area to be repaired., Determine if the damaged area will require fiberglass cloth reinforcing., Read the mixing and tinting instructions of the product you have purchased., Place a...
Step-by-Step Guide
-
Step 1: Purchase a suitable kit for your shower (or bathtub).
You should make sure your shower or bathtub is fiberglass before going shopping, as these instructions will not give good results on cast iron or other types of fixtures.
Make sure your shower is fiberglass by tapping it with your knuckle or a wooden spoon or similar item which will not damage the finish.
A fiberglass unit will have a soft, hollow, non-metallic sound, and depending on where you tap it, may even seem flexible.
Choose the appropriate color for the kit you will purchase.
Most kits come with colorants (tinting products) to change the color of the product to match common colored fixtures, such as white, off white, or almond.
Make sure the kit you buy comes complete with everything you need, or purchase these materials and tools separately.
The following is a list of what your kit may contain:
Polyester resin Hardener (catalyst to harden the resin) Fiberglass mesh or mat (for large or structural repairs) Colorants Sandpaper in assorted grits, from 80 grit (coarse) to 400 or 440 grit (very fine) Thickener (to stiffen the resin for vertical applications) Protective gloves resistant to the chemicals included in the kit A mixing container and stirring tool -
Step 2: Clean the area to be repaired.
Cut any jagged or protruding glass fibers around the damaged area, sand it lightly with a medium grit sandpaper to remove wax, oil, soap scum, or other surface contaminants, and rinse with acetone or another solvent to assure proper adhesion of the repair product. , If it does not, skip to the step describing mixing and tinting instructions.
If the crack is over one fourth of an inch (1/2 cm) wide, or is actually an open hole that the resin mixture will not fill alone, cut a piece of fiberglass mesh or cloth slightly larger than the hole.
For large holes or cracks, more than one layer of cloth may be needed to get good results. , Since individual products may vary, and measuring the materials you mix is essential, make sure you understand these instructions before proceeding. , Place the container you will mix in (usually supplied in the kit you purchased) on this surface. , Most kits have mixing proportions for fractional portions of the resin provided, such as 1/4th of the volume, 1/2, etc., mixed with an equal proportion of hardener. , An example would be for almond, mix 5 parts white with 1 part brown, to 20 parts of resin.
For basic white, use the white colorant added until the resin is thoroughly opaque.
Mix these components thoroughly, and check the color against the fixture you are repairing before adding the hardener. , Vertical surfaces need to be very stiff so the product does not sag, drip, or run.
For horizontal repairs the material can be thinner, but it still should be stiff enough that it can be tooled smooth with the applicator. , If you cannot find a workable proportion, you may have to make an educated guess as to how much you will need.
Generally speaking, too much hardener will only accelerate the process, allowing less working time, and too little will delay the setting time.
If you fail to add enough hardener to set the resin, however, it will remain tacky indefinitely.
For a ball-park estimate, add 5 drops of hardener to each tablespoon of resin/colorant mixture. , The longer you stir the material, the better the results will be, making sure that all of edges and corners are incorporated so that it hardens equally.
Remember, though, that once you add the hardener, the reaction that solidifies the resin will begin, so you can only expect 10 to 15 minutes total working time before the resin becomes unusable. , If you are using fiberglass cloth for your repair, place the piece you have cut over the damage, and press it into the resin repair mixture.
Make sure you spread it evenly, and to a level slightly higher than the original surface so it can be sanded down and feathered smooth when you finish.
Once the repair material is applied, allow it to harden, typically about 2 hours at room temperature. , If you used fiberglass cloth, you may need to trim any fibers that are protruding with a sharp utility knife before sanding.
Begin with a fairly coarse grit of sandpaper, depending on how much of the patch has to be removed to make it flush with the original surface.
Work your way from a coarse or medium grit to a fine, then very fine grit sandpaper, until the repair is smooth.
If you need to build up the repair further, mix another application and apply it to the damaged area, then repeat the sanding. , You can apply this with a small artist's paintbrush, or if it is a small chip or ding, even a cotton swab will do.
Smooth this application as much as possible, allow it to harden, then sand it with very fine sandpaper. ,, -
Step 3: Determine if the damaged area will require fiberglass cloth reinforcing.
-
Step 4: Read the mixing and tinting instructions of the product you have purchased.
-
Step 5: Place a protective material like cardboard or heavy construction paper on the surface you will mix the material on.
-
Step 6: Measure the amount of polyester resin into the mixing container you think you will need for your repair.
-
Step 7: Add the colorant from the correct tube that came with the kit.
-
Step 8: Mix thickening material into the resin/colorant mixture until it is a desired consistency for your patch.
-
Step 9: Add the hardener according to the kit's instructions.
-
Step 10: Mix the repair material thoroughly.
-
Step 11: Using a flat tool like a putty knife or wooden tongue depressor
-
Step 12: scoop out some of the mixture and apply it to the damaged area.
-
Step 13: Sand the patch carefully
-
Step 14: trying not to scuff the adjacent areas.
-
Step 15: Mix another batch of resin and colorant to overlay the first patch
-
Step 16: without the thickening agent.
-
Step 17: Buff the finished repair with the buffing compound provided in the kit to restore the gloss finish so it matches the original.
-
Step 18: Clean up the area
-
Step 19: and admire your handiwork.
Detailed Guide
You should make sure your shower or bathtub is fiberglass before going shopping, as these instructions will not give good results on cast iron or other types of fixtures.
Make sure your shower is fiberglass by tapping it with your knuckle or a wooden spoon or similar item which will not damage the finish.
A fiberglass unit will have a soft, hollow, non-metallic sound, and depending on where you tap it, may even seem flexible.
Choose the appropriate color for the kit you will purchase.
Most kits come with colorants (tinting products) to change the color of the product to match common colored fixtures, such as white, off white, or almond.
Make sure the kit you buy comes complete with everything you need, or purchase these materials and tools separately.
The following is a list of what your kit may contain:
Polyester resin Hardener (catalyst to harden the resin) Fiberglass mesh or mat (for large or structural repairs) Colorants Sandpaper in assorted grits, from 80 grit (coarse) to 400 or 440 grit (very fine) Thickener (to stiffen the resin for vertical applications) Protective gloves resistant to the chemicals included in the kit A mixing container and stirring tool
Cut any jagged or protruding glass fibers around the damaged area, sand it lightly with a medium grit sandpaper to remove wax, oil, soap scum, or other surface contaminants, and rinse with acetone or another solvent to assure proper adhesion of the repair product. , If it does not, skip to the step describing mixing and tinting instructions.
If the crack is over one fourth of an inch (1/2 cm) wide, or is actually an open hole that the resin mixture will not fill alone, cut a piece of fiberglass mesh or cloth slightly larger than the hole.
For large holes or cracks, more than one layer of cloth may be needed to get good results. , Since individual products may vary, and measuring the materials you mix is essential, make sure you understand these instructions before proceeding. , Place the container you will mix in (usually supplied in the kit you purchased) on this surface. , Most kits have mixing proportions for fractional portions of the resin provided, such as 1/4th of the volume, 1/2, etc., mixed with an equal proportion of hardener. , An example would be for almond, mix 5 parts white with 1 part brown, to 20 parts of resin.
For basic white, use the white colorant added until the resin is thoroughly opaque.
Mix these components thoroughly, and check the color against the fixture you are repairing before adding the hardener. , Vertical surfaces need to be very stiff so the product does not sag, drip, or run.
For horizontal repairs the material can be thinner, but it still should be stiff enough that it can be tooled smooth with the applicator. , If you cannot find a workable proportion, you may have to make an educated guess as to how much you will need.
Generally speaking, too much hardener will only accelerate the process, allowing less working time, and too little will delay the setting time.
If you fail to add enough hardener to set the resin, however, it will remain tacky indefinitely.
For a ball-park estimate, add 5 drops of hardener to each tablespoon of resin/colorant mixture. , The longer you stir the material, the better the results will be, making sure that all of edges and corners are incorporated so that it hardens equally.
Remember, though, that once you add the hardener, the reaction that solidifies the resin will begin, so you can only expect 10 to 15 minutes total working time before the resin becomes unusable. , If you are using fiberglass cloth for your repair, place the piece you have cut over the damage, and press it into the resin repair mixture.
Make sure you spread it evenly, and to a level slightly higher than the original surface so it can be sanded down and feathered smooth when you finish.
Once the repair material is applied, allow it to harden, typically about 2 hours at room temperature. , If you used fiberglass cloth, you may need to trim any fibers that are protruding with a sharp utility knife before sanding.
Begin with a fairly coarse grit of sandpaper, depending on how much of the patch has to be removed to make it flush with the original surface.
Work your way from a coarse or medium grit to a fine, then very fine grit sandpaper, until the repair is smooth.
If you need to build up the repair further, mix another application and apply it to the damaged area, then repeat the sanding. , You can apply this with a small artist's paintbrush, or if it is a small chip or ding, even a cotton swab will do.
Smooth this application as much as possible, allow it to harden, then sand it with very fine sandpaper. ,,
About the Author
Martha Roberts
Enthusiastic about teaching DIY projects techniques through clear, step-by-step guides.
Rate This Guide
How helpful was this guide? Click to rate: