How to Clean Gourds
Soak the gourd in water for 30 minutes., Put on gloves and a face mask., Scrub the gourds to remove the skin., Use detergent or bleach to remove mold., Scrape off stubborn mold., Dry the gourd., Sand off any leftover skin., Put on safety gear., Cut...
Step-by-Step Guide
-
Step 1: Soak the gourd in water for 30 minutes.
Submerge the gourds in buckets of water.
Allow the skins to soak.
If you do not have buckets, other options include covering them with wet towels or letting them sit out under a sprinkler.
Allow them to sit for 30 minutes and the hard gourd skin will soften.Avoid using hot water, as this can cause the gourd to crack. -
Step 2: Put on gloves and a face mask.
Before cleaning the gourd, take safety precautions.
Work in a well-ventilated area.
Put on rubber kitchen gloves and a dust mask to protect against the mold that grows on the outside of gourds., Use a copper dish scrubber, a non-scratch scouring pad, or other similar cleaning utensil.
Press hard while scrubbing to remove the skin, but try to hold back a little to avoid scratching the gourd itself.
This can be done while the gourd is wet or in water.
Water exposure makes the skin come off easier and, as long as the gourd doesn’t have holes in it, won’t damage the gourd.Avoid using steel wool.
It tends to leave metal particles on the gourd. , When the mold forms a white film that’s tough to get out, try squirting liquid dish soap over it.
The gourd is tough, so any regular dish soap you use will work.
Scrub the gourd again.
When the mold still won’t go away, try dipping the gourd in a 10% solution of bleach (ten parts water to one part bleach) or about two cups (473 mL) of chlorine bleach to five gallons (18.9 L) water and scrubbing the gourd., When washing and scrubbing doesn’t seem to work, a sharp knife or sander may work.
Carefully place these objects against the skin of the gourd.
Scrape off the mold, taking care not to cut into the gourd., You can rinse the gourd again to make sure all the skin is gone.
Once this is done, leave the gourd in a shady, ventilated area.
It should dry quickly. , This is not required, but can be done to ensure the gourd is skinless or even extra smooth.
Use a sanding block, sandpaper, or a sander.
Start with 80 grit paper and switch to a higher grade of sandpaper for a smoother gourd., Rubber gloves are useful again for handling gourds that may still have mold or other harmful substances on them.
Work in a ventilated environment and wear a dust mask because of the dust inside the gourd.
Finally, wear eye protection when using power tools. , The way you cut the gourd and the tool you use depends on your intended use.
For example, a power drill can be used to make a hole for a birdhouse, or you can cut an opening using hand saws and rotary cutters to make a decorative container., Birds don’t mind the papery pulp and seeds inside the gourd, but you will have to get rid of them when making something other than a birdhouse.
Tools with long handles, such as clay sculpting tools, spoons, and screwdrivers can help you reach the seeds and scrape pulp off the walls of the gourd.
When the opening is too small or the seeds are in a tough ball, you can soak the gourd in warm water for 30 minutes.
However, it will take several hours for the gourd to dry.Pulp and seeds can be saved for projects such as replanting or pulp sculptures by straining them and letting them dry in a single layer., Depending on your product, such as when making a bowl, you may wish to make the inside of the gourd smooth.
Use your sanding tool.
Afterwards, you may wish to add primer, dye, or paint to decorate the gourd.Gourd Ball cleaner or a mushroom tool, which is used to cut off the caps of mushrooms, can also be used to sand the inside of the gourd. -
Step 3: Scrub the gourds to remove the skin.
-
Step 4: Use detergent or bleach to remove mold.
-
Step 5: Scrape off stubborn mold.
-
Step 6: Dry the gourd.
-
Step 7: Sand off any leftover skin.
-
Step 8: Put on safety gear.
-
Step 9: Cut the gourd.
-
Step 10: Scrape out the inside of the gourd.
-
Step 11: Sand the inside of the gourd.
Detailed Guide
Submerge the gourds in buckets of water.
Allow the skins to soak.
If you do not have buckets, other options include covering them with wet towels or letting them sit out under a sprinkler.
Allow them to sit for 30 minutes and the hard gourd skin will soften.Avoid using hot water, as this can cause the gourd to crack.
Before cleaning the gourd, take safety precautions.
Work in a well-ventilated area.
Put on rubber kitchen gloves and a dust mask to protect against the mold that grows on the outside of gourds., Use a copper dish scrubber, a non-scratch scouring pad, or other similar cleaning utensil.
Press hard while scrubbing to remove the skin, but try to hold back a little to avoid scratching the gourd itself.
This can be done while the gourd is wet or in water.
Water exposure makes the skin come off easier and, as long as the gourd doesn’t have holes in it, won’t damage the gourd.Avoid using steel wool.
It tends to leave metal particles on the gourd. , When the mold forms a white film that’s tough to get out, try squirting liquid dish soap over it.
The gourd is tough, so any regular dish soap you use will work.
Scrub the gourd again.
When the mold still won’t go away, try dipping the gourd in a 10% solution of bleach (ten parts water to one part bleach) or about two cups (473 mL) of chlorine bleach to five gallons (18.9 L) water and scrubbing the gourd., When washing and scrubbing doesn’t seem to work, a sharp knife or sander may work.
Carefully place these objects against the skin of the gourd.
Scrape off the mold, taking care not to cut into the gourd., You can rinse the gourd again to make sure all the skin is gone.
Once this is done, leave the gourd in a shady, ventilated area.
It should dry quickly. , This is not required, but can be done to ensure the gourd is skinless or even extra smooth.
Use a sanding block, sandpaper, or a sander.
Start with 80 grit paper and switch to a higher grade of sandpaper for a smoother gourd., Rubber gloves are useful again for handling gourds that may still have mold or other harmful substances on them.
Work in a ventilated environment and wear a dust mask because of the dust inside the gourd.
Finally, wear eye protection when using power tools. , The way you cut the gourd and the tool you use depends on your intended use.
For example, a power drill can be used to make a hole for a birdhouse, or you can cut an opening using hand saws and rotary cutters to make a decorative container., Birds don’t mind the papery pulp and seeds inside the gourd, but you will have to get rid of them when making something other than a birdhouse.
Tools with long handles, such as clay sculpting tools, spoons, and screwdrivers can help you reach the seeds and scrape pulp off the walls of the gourd.
When the opening is too small or the seeds are in a tough ball, you can soak the gourd in warm water for 30 minutes.
However, it will take several hours for the gourd to dry.Pulp and seeds can be saved for projects such as replanting or pulp sculptures by straining them and letting them dry in a single layer., Depending on your product, such as when making a bowl, you may wish to make the inside of the gourd smooth.
Use your sanding tool.
Afterwards, you may wish to add primer, dye, or paint to decorate the gourd.Gourd Ball cleaner or a mushroom tool, which is used to cut off the caps of mushrooms, can also be used to sand the inside of the gourd.
About the Author
Thomas Gray
A passionate writer with expertise in creative arts topics. Loves sharing practical knowledge.
Rate This Guide
How helpful was this guide? Click to rate: