How to Touch Up Car Paint
Buy a matching touch-up paint color., Check the affected area for rust., Wash the car, focusing on the area where the paint is chipped. , Pre-treat the chip., Apply primer if necessary., Test the paint., Paint the primed area., Finish the surface.
Step-by-Step Guide
-
Step 1: Buy a matching touch-up paint color.
Check the firewall (bulkhead) to find the paint code number.
The firewall is the piece of sheet metal that separates the engine under the hood from the passengers inside the vehicle.
You will need to open your hood to find this number.
Purchase a primer along with the touch-up paint unless the particular touch-up paint you've chosen states otherwise.
Touch-up paint and primer can be purchased at auto stores. -
Step 2: Check the affected area for rust.
Apply a small amount of rust arrestor on the chipped area before touching it up to prevent rust from spreading underneath your touch-up job. ,, Apply wax remover to the area.
Use a nick sander to remove all loose paint from the area.
Sand the area again with number 220 sandpaper.
This will allow the primer to stick.
Wash the area once more with water to remove the wax and any leftover debris from the pre-treating process.
Allow the area to dry thoroughly before moving on to the next step. , Squeeze a dab of primer onto the area if the chip reaches metal.
If the chip is surface-level, you can skip this step.
Primer is needed for deep chips because regular paint will not adhere to bare metal.
Spread the primer around the small chip with a tiny brush.
Only use enough primer for one thin coat.
Allow the primer to dry completely. , Apply some of the paint to an area on the car that isn't visible, such as the lip under a door.
It is important to make sure the paint you've purchased will not react poorly to your existing paint and also that it matches well. , Shake the paint well and pour some into a shallow dish.
Spread 2 to 3 layers of touch-up paint on the area.
The touched-up spot will look elevated above the rest of the paint, which is how it should look.
Wait at least 24 hours before continuing the process. , Sand the area with 1000-grit sandpaper, making sure to move very slowly and gently.
Continue with 2000-grit and 3000-grit until the touch-up paint is even with the rest of the vehicle.
Polish and wax the entire car. -
Step 3: Wash the car
-
Step 4: focusing on the area where the paint is chipped.
-
Step 5: Pre-treat the chip.
-
Step 6: Apply primer if necessary.
-
Step 7: Test the paint.
-
Step 8: Paint the primed area.
-
Step 9: Finish the surface.
Detailed Guide
Check the firewall (bulkhead) to find the paint code number.
The firewall is the piece of sheet metal that separates the engine under the hood from the passengers inside the vehicle.
You will need to open your hood to find this number.
Purchase a primer along with the touch-up paint unless the particular touch-up paint you've chosen states otherwise.
Touch-up paint and primer can be purchased at auto stores.
Apply a small amount of rust arrestor on the chipped area before touching it up to prevent rust from spreading underneath your touch-up job. ,, Apply wax remover to the area.
Use a nick sander to remove all loose paint from the area.
Sand the area again with number 220 sandpaper.
This will allow the primer to stick.
Wash the area once more with water to remove the wax and any leftover debris from the pre-treating process.
Allow the area to dry thoroughly before moving on to the next step. , Squeeze a dab of primer onto the area if the chip reaches metal.
If the chip is surface-level, you can skip this step.
Primer is needed for deep chips because regular paint will not adhere to bare metal.
Spread the primer around the small chip with a tiny brush.
Only use enough primer for one thin coat.
Allow the primer to dry completely. , Apply some of the paint to an area on the car that isn't visible, such as the lip under a door.
It is important to make sure the paint you've purchased will not react poorly to your existing paint and also that it matches well. , Shake the paint well and pour some into a shallow dish.
Spread 2 to 3 layers of touch-up paint on the area.
The touched-up spot will look elevated above the rest of the paint, which is how it should look.
Wait at least 24 hours before continuing the process. , Sand the area with 1000-grit sandpaper, making sure to move very slowly and gently.
Continue with 2000-grit and 3000-grit until the touch-up paint is even with the rest of the vehicle.
Polish and wax the entire car.
About the Author
Joseph Ross
Writer and educator with a focus on practical lifestyle knowledge.
Rate This Guide
How helpful was this guide? Click to rate: