How to Make a Kite Shield

Pick up some supplies., Now, get yourself some red vinyl tape., Cut the sheet down to 3 or 4 feet (0.9 or 1.2 m)., Using a coffee can, place it on the corner of the plywood and trace the edge.,Cut the marked area off on every corner., Using a...

21 Steps 1 min read Advanced

Step-by-Step Guide

  1. Step 1: Pick up some supplies.

    Hardware store carries sheets of plywood.

    Make sure you get at least 1⁄4 inch (0.6 cm) thick, but no more than 1⁄2 inch (1.3 cm) thick.

    Get at least 3 feet (0.9 m). tall and 1 foot (0.3 m). wide. , This isn't necessary, but it really improves the look of the shield.

    And hey, who doesn't want a nice Templar cross on their shield?, tall, and 1 foot (0.3 m). wide.

    Use an automatic saw., It should give the shield a rounded corner.,, |\/|.

    Like that.

    Now, cut off the two triangles.

    Your shield should now have a kite appearance.,, (Or any other shape.

    Try to run with this idea in terms of decoration.),,,,,
  2. Step 2: get yourself some red vinyl tape.

  3. Step 3: Cut the sheet down to 3 or 4 feet (0.9 or 1.2 m).

  4. Step 4: Using a coffee can

  5. Step 5: place it on the corner of the plywood and trace the edge.

  6. Step 6: Cut the marked area off on every corner.

  7. Step 7: Using a straight-edge

  8. Step 8: draw two isosceles triangles on the bottom of the shield whose corners meet at the center of the shield.

  9. Step 9: Spray paint whichever side will be facing outwards gold or silver.

  10. Step 10: Using the vinyl tape from earlier

  11. Step 11: make a nice cross on the front.

  12. Step 12: mark 5 inches (12.7 cm) in and-- depending on the height of the shield-- 10 inches (25.4 cm) from the top.

  13. Step 13: Mark 5 inches (12.7 cm) below this mark

  14. Step 14: and six inches across from each one.

  15. Step 15: Line up a five inch strap of leather with two of the vertically connected marks.

  16. Step 16: Drill a hole through the leather and wood

  17. Step 17: then screw through

  18. Step 18: slide on a wing

  19. Step 19: wrench on a nut

  20. Step 20: and cut off any screw that hangs past the mark.

  21. Step 21: Repeat with the other two marks.

Detailed Guide

Hardware store carries sheets of plywood.

Make sure you get at least 1⁄4 inch (0.6 cm) thick, but no more than 1⁄2 inch (1.3 cm) thick.

Get at least 3 feet (0.9 m). tall and 1 foot (0.3 m). wide. , This isn't necessary, but it really improves the look of the shield.

And hey, who doesn't want a nice Templar cross on their shield?, tall, and 1 foot (0.3 m). wide.

Use an automatic saw., It should give the shield a rounded corner.,, |\/|.

Like that.

Now, cut off the two triangles.

Your shield should now have a kite appearance.,, (Or any other shape.

Try to run with this idea in terms of decoration.),,,,,

About the Author

D

Debra Walker

Experienced content creator specializing in pet care guides and tutorials.

27 articles
View all articles

Rate This Guide

--
Loading...
5
0
4
0
3
0
2
0
1
0

How helpful was this guide? Click to rate: