How to Make a Mondrian Pattern
Choose a canvas or surface onto which you will place your design like a tabletop or onto a wall as a mural, directly., Depending on the size of your chosen canvas or surface, you will need to adapt the quantities accordingly., Start by priming the...
Step-by-Step Guide
-
Step 1: Choose a canvas or surface onto which you will place your design like a tabletop or onto a wall as a mural
Ensure that it is clean, dry and free from oil (as these marks may show through the finished piece). -
Step 2: directly.
The tape used to mask will need to depend on the proportion to this surface also, for the most authentic Mondrian "feel".
You will need the following:
Reference material
- or a sketch of your own design Canvas or flat surface to decorate on.
Pencil Tape measure Tape for masking off square areas and lines Sharp scissors Acrylic paints in these colours:
White, black, cobalt blue, cadmium yellow, red madder (or an orange-red) Brushes
- any will work, you will need one large brush for priming in black, and perhaps one for each colour will save you washing out thoroughly between colour changes. (Optional) Varnish to seal your work
- vital if your design is going on to a work surface or somewhere that gets heavy wear and tear.
Room to step back from the painting at the masking stage and check your lines! ,, Mark these lightly along the sides, and then rule out straight lines across the canvas, corresponding point to corresponding point. , Apply your tape to the black surface, using your pencil lines as guides, to create the blocks we will later fill with colour.
Be sure to cut the tape neatly and as squarely as possible, and as you apply it place the cut end of the tape up to the outside edge of the last piece of tape to 'box in' the colour and ensure clean, crisp lines. , Until it is a solid, uniform white.
Patience is needed here!*If you want black blocks of colour in your designs, obviously do not paint past the taped lines in these areas, leave them black. , Remember
- less is more until you're sure you're happy with the design.
Keep looking back to Mondrian's work for guidance, or use your imagination! This bit is up to you! , Carefully peel away the tape to reveal the black lines and complete the work
- et voila! Protect your new design with appropriate sealer or varnish, and once dry, stand back and admire! -
Step 3: Depending on the size of your chosen canvas or surface
-
Step 4: you will need to adapt the quantities accordingly.
-
Step 5: Start by priming the surface in black - two to three coats
-
Step 6: allowing each to dry before applying the next.
-
Step 7: Using your tape measure and pencil
-
Step 8: divide the canvas into a grid of squares by measuring equal points along the edges.
-
Step 9: This is where your reference material comes in and where you should take the most time.
-
Step 10: Make sure your tape is stuck firmly
-
Step 11: and give the whole canvas* another two to three coats of white paint.
-
Step 12: Leaving all tape in place when the white paint is dry
-
Step 13: begin filling in blocks of colour as you wish.
-
Step 14: When all paint is dry (overnight to be sure) - the big reveal!
Detailed Guide
Ensure that it is clean, dry and free from oil (as these marks may show through the finished piece).
The tape used to mask will need to depend on the proportion to this surface also, for the most authentic Mondrian "feel".
You will need the following:
Reference material
- or a sketch of your own design Canvas or flat surface to decorate on.
Pencil Tape measure Tape for masking off square areas and lines Sharp scissors Acrylic paints in these colours:
White, black, cobalt blue, cadmium yellow, red madder (or an orange-red) Brushes
- any will work, you will need one large brush for priming in black, and perhaps one for each colour will save you washing out thoroughly between colour changes. (Optional) Varnish to seal your work
- vital if your design is going on to a work surface or somewhere that gets heavy wear and tear.
Room to step back from the painting at the masking stage and check your lines! ,, Mark these lightly along the sides, and then rule out straight lines across the canvas, corresponding point to corresponding point. , Apply your tape to the black surface, using your pencil lines as guides, to create the blocks we will later fill with colour.
Be sure to cut the tape neatly and as squarely as possible, and as you apply it place the cut end of the tape up to the outside edge of the last piece of tape to 'box in' the colour and ensure clean, crisp lines. , Until it is a solid, uniform white.
Patience is needed here!*If you want black blocks of colour in your designs, obviously do not paint past the taped lines in these areas, leave them black. , Remember
- less is more until you're sure you're happy with the design.
Keep looking back to Mondrian's work for guidance, or use your imagination! This bit is up to you! , Carefully peel away the tape to reveal the black lines and complete the work
- et voila! Protect your new design with appropriate sealer or varnish, and once dry, stand back and admire!
About the Author
Peter Jenkins
Peter Jenkins is an experienced writer with over 17 years of expertise in consulting. Passionate about sharing practical knowledge, Peter creates easy-to-follow guides that help readers achieve their goals.
Rate This Guide
How helpful was this guide? Click to rate: