How to Read a Hydrometer
Check your hydrometer's temperature calibration., Measure the temperature of the liquid., Pour a sample into a clean container., Insert the hydrometer into the liquid., Spin the hydrometer gently., Read the hydrometer scale at the lowest point of...
Step-by-Step Guide
-
Step 1: Check your hydrometer's temperature calibration.
Hydrometers measure the density of liquid, but liquids expand and contract with temperature changes.
In order to get an accurate answer, you need to test liquids at the temperature your hydrometer was designed for.
This temperature should be listed on the hydrometer label, or on instructions in the same package.
Most homebrew hydrometers are calibrated at 59–60°F (15–15.6°C ), and most laboratory hydrometers are calibrated at 68°F (20.0°C).Hydrometers can lose accuracy over time.
If you're using an old tool, you may want to test it first. -
Step 2: Measure the temperature of the liquid.
If this is more than a degree or two off from the hydrometer's intended temperature, write down the result.
Your measurement will be off, but you can correct it using the temperature chart at the end of this article.
If testing homebrewed wort, do not contaminate it with a non-sanitized thermometer.
Use an adhesive strip thermometer that sticks to the side of the container, or measure a sample instead of the main batch. , Choose a transparent jar or cup large enough that the hydrometer can float without hitting the sides or bottom of the container.
Transfer a sample of the liquid into this container.
When brewing, test the wort after visible signs of fermentation have ended, but before pitching the yeast.
Transfer the sample using a sanitized siphon, wine thief, or baster.If precision is extremely important, rinse the container with a small amount of the liquid before adding the full sample. , Make sure the hydrometer is dry, then lower it into the liquid just below the point at which it would float naturally.
Be sure the hydrometer bulb does not touch the sides or bottom of the jar when it settles. , This will dislodge air bubbles clinging to the tool, which would disrupt the measurement.
Wait for the hydrometer and the liquid to stop moving, and for bubbles to dissipate. , The surface of the fluid may cling to the hydrometer and the container walls, forming a curve called a meniscus.
Look for the scale mark on the hydrometer level with the lowest point on the fluid's surface.
Do not use the mark where the fluid touches the hydrometer., The most common scale on hydrometers is "specific gravity." This is the ratio of the liquid's density to the density of water.
Pure water should give a reading of
1.000.
A higher reading means the liquid is denser (heavier) than water, and a lower reading means it is lighter.
The specific gravity of wort (called original gravity or OG by brewers) varies greatly.
The more sugar in a wort, the higher the OG, and the higher alcohol content in the final beer.
Most beers OGs fall in the
1.030 to
1.070 range, but they can be significantly higher., Your hydrometer may use one of these scales instead, or you may need to convert your measurement to follow a certain recipe.
Here's how to measure density using these three units:
The Plato scale measures the percentage of sucrose in a wort, so 10 degrees on the Plato scale means 10% of the wort is sucrose by weight.
Multiply the Plato measurement by
0.004 and add 1 for a specific gravity estimate that's close enough for home brewing purposes.For example, a 10 degrees Plato wort has a specific gravity of 10 x .004 + 1 =
1.040. (The further you get from this number, the less accurate the conversion is.) The Balling and Brix scales are close enough to the Plato scale that you can use the units interchangeably for home brewing.
Commercial breweries use more exact conversion formulas, and conduct their own tests to calibrate the Brix scale based on various factors., At the end of the entire brewing process, test additional samples daily with the hydrometer.
If the reading is the same two days in a row, no more sugars are being converted into alcohol, meaning fermentation is complete.
The final reading at this point is the "final gravity" or "FG." The target FG depends on what kind of brew you are making, and in some cases on additional ingredients that affect the hydrometer reading.
With a few exceptions, most beers have an FG around
1.007 to
1.015.Home brewers rarely get the exact FG predicted by their recipe, especially on their first few attempts.
It's more important that the beer tastes good, but keep records and keep studying the process to get a more consistent result. , The difference between the original gravity and final gravity tells you how much sugar was converted to alcohol.
The formula
132.715 x (OG
- FG) is a useful way to convert this into alcohol by volume (ABV).
Note that this is only an estimate, and is most accurate for beers with a final gravity around
1.010.For example, if your OG was
1.041 and your FG is
1.011, the ABV is roughly
132.715 x (1.041
-
1.011) =
3.98%. , To test whether the hydrometer is accurate, use distilled water or reverse osmosis water.
If you use tap water or untreated bottled water in your brewing, you can test with that instead.
The mineral content will alter the results, but this will tell you how to adjust your readings for brews made with that specific water. , The hydrometer's calibrated temperature should be marked on the hydrometer label or the package instructions. , Place the hydrometer in the water, spin gently to shake off air bubbles, and wait for it to settle.
The hydrometer will read
1.000 for pure water if it is perfectly calibrated.
A hydrometer that uses the Plato or Balling scale will read
0.00º.See the instructions above for a more detailed guide on how to use the hydrometer. , If you get a result other than
1.000, the hydrometer is off (or your water contains minerals).
Write down the amount you need to add or subtract to future readings to correct this error.For example, if your hydrometer reads
0.999 in pure water, add
0.001 to all measurements.
To take another example, if your hydrometer reads
1.003 in tap water, subtract
0.003 from all measurements of liquid brewed with that specific tap water.
Test the hydrometer again if you change water sources. , If your hydrometer is significantly off, it's often best to order a new one.
The old one may lose even more accuracy over time, but it is possible for the frugal brewer to correct it:
If the measurement is too low, attach tape, nail polish, or any other material to increase the weight until the measurement is correct.
If the measurement is too high, file the edge to remove material.
Seal the rough area with nail polish to protect against glass dust or sharp edges. -
Step 3: Pour a sample into a clean container.
-
Step 4: Insert the hydrometer into the liquid.
-
Step 5: Spin the hydrometer gently.
-
Step 6: Read the hydrometer scale at the lowest point of the liquid's surface.
-
Step 7: Understand the measurement.
-
Step 8: Interpret the Plato
-
Step 9: Balling
-
Step 10: or Brix scales.
-
Step 11: Take a reading of the final brew.
-
Step 12: Estimate alcohol by volume.
-
Step 13: Fill a container with water.
-
Step 14: Bring the water to the correct temperature.
-
Step 15: Measure the density of the water.
-
Step 16: Write down the correction if the hydrometer is inaccurate.
-
Step 17: Consider replacing or adjusting your hydrometer.
Detailed Guide
Hydrometers measure the density of liquid, but liquids expand and contract with temperature changes.
In order to get an accurate answer, you need to test liquids at the temperature your hydrometer was designed for.
This temperature should be listed on the hydrometer label, or on instructions in the same package.
Most homebrew hydrometers are calibrated at 59–60°F (15–15.6°C ), and most laboratory hydrometers are calibrated at 68°F (20.0°C).Hydrometers can lose accuracy over time.
If you're using an old tool, you may want to test it first.
If this is more than a degree or two off from the hydrometer's intended temperature, write down the result.
Your measurement will be off, but you can correct it using the temperature chart at the end of this article.
If testing homebrewed wort, do not contaminate it with a non-sanitized thermometer.
Use an adhesive strip thermometer that sticks to the side of the container, or measure a sample instead of the main batch. , Choose a transparent jar or cup large enough that the hydrometer can float without hitting the sides or bottom of the container.
Transfer a sample of the liquid into this container.
When brewing, test the wort after visible signs of fermentation have ended, but before pitching the yeast.
Transfer the sample using a sanitized siphon, wine thief, or baster.If precision is extremely important, rinse the container with a small amount of the liquid before adding the full sample. , Make sure the hydrometer is dry, then lower it into the liquid just below the point at which it would float naturally.
Be sure the hydrometer bulb does not touch the sides or bottom of the jar when it settles. , This will dislodge air bubbles clinging to the tool, which would disrupt the measurement.
Wait for the hydrometer and the liquid to stop moving, and for bubbles to dissipate. , The surface of the fluid may cling to the hydrometer and the container walls, forming a curve called a meniscus.
Look for the scale mark on the hydrometer level with the lowest point on the fluid's surface.
Do not use the mark where the fluid touches the hydrometer., The most common scale on hydrometers is "specific gravity." This is the ratio of the liquid's density to the density of water.
Pure water should give a reading of
1.000.
A higher reading means the liquid is denser (heavier) than water, and a lower reading means it is lighter.
The specific gravity of wort (called original gravity or OG by brewers) varies greatly.
The more sugar in a wort, the higher the OG, and the higher alcohol content in the final beer.
Most beers OGs fall in the
1.030 to
1.070 range, but they can be significantly higher., Your hydrometer may use one of these scales instead, or you may need to convert your measurement to follow a certain recipe.
Here's how to measure density using these three units:
The Plato scale measures the percentage of sucrose in a wort, so 10 degrees on the Plato scale means 10% of the wort is sucrose by weight.
Multiply the Plato measurement by
0.004 and add 1 for a specific gravity estimate that's close enough for home brewing purposes.For example, a 10 degrees Plato wort has a specific gravity of 10 x .004 + 1 =
1.040. (The further you get from this number, the less accurate the conversion is.) The Balling and Brix scales are close enough to the Plato scale that you can use the units interchangeably for home brewing.
Commercial breweries use more exact conversion formulas, and conduct their own tests to calibrate the Brix scale based on various factors., At the end of the entire brewing process, test additional samples daily with the hydrometer.
If the reading is the same two days in a row, no more sugars are being converted into alcohol, meaning fermentation is complete.
The final reading at this point is the "final gravity" or "FG." The target FG depends on what kind of brew you are making, and in some cases on additional ingredients that affect the hydrometer reading.
With a few exceptions, most beers have an FG around
1.007 to
1.015.Home brewers rarely get the exact FG predicted by their recipe, especially on their first few attempts.
It's more important that the beer tastes good, but keep records and keep studying the process to get a more consistent result. , The difference between the original gravity and final gravity tells you how much sugar was converted to alcohol.
The formula
132.715 x (OG
- FG) is a useful way to convert this into alcohol by volume (ABV).
Note that this is only an estimate, and is most accurate for beers with a final gravity around
1.010.For example, if your OG was
1.041 and your FG is
1.011, the ABV is roughly
132.715 x (1.041
-
1.011) =
3.98%. , To test whether the hydrometer is accurate, use distilled water or reverse osmosis water.
If you use tap water or untreated bottled water in your brewing, you can test with that instead.
The mineral content will alter the results, but this will tell you how to adjust your readings for brews made with that specific water. , The hydrometer's calibrated temperature should be marked on the hydrometer label or the package instructions. , Place the hydrometer in the water, spin gently to shake off air bubbles, and wait for it to settle.
The hydrometer will read
1.000 for pure water if it is perfectly calibrated.
A hydrometer that uses the Plato or Balling scale will read
0.00º.See the instructions above for a more detailed guide on how to use the hydrometer. , If you get a result other than
1.000, the hydrometer is off (or your water contains minerals).
Write down the amount you need to add or subtract to future readings to correct this error.For example, if your hydrometer reads
0.999 in pure water, add
0.001 to all measurements.
To take another example, if your hydrometer reads
1.003 in tap water, subtract
0.003 from all measurements of liquid brewed with that specific tap water.
Test the hydrometer again if you change water sources. , If your hydrometer is significantly off, it's often best to order a new one.
The old one may lose even more accuracy over time, but it is possible for the frugal brewer to correct it:
If the measurement is too low, attach tape, nail polish, or any other material to increase the weight until the measurement is correct.
If the measurement is too high, file the edge to remove material.
Seal the rough area with nail polish to protect against glass dust or sharp edges.
About the Author
Evelyn Bishop
Experienced content creator specializing in pet care guides and tutorials.
Rate This Guide
How helpful was this guide? Click to rate: