How to Weave Rope Seats
Gather rope, shuttles, spacers, and a crochet hook, from a local craft store., Tie the first half of your rope to one of the horizontal seat poles using a clove hitch., Lay the 1" spacer across the seat, perpendicular to your knot., Wrap the rope...
Step-by-Step Guide
-
Step 1: Gather rope
The materials needed are light and easy, though you may have some questions about how much you actually need:
About 2lbs of rope chord, cut into two roughly even halves (roughly 200 ft) 2-3 completely flat, 1/8" thick weaving shuttles, (various lengths) 1" thick wooden spacer, same length as chair 1/2" thick wooden spacer, same length as chair Very thin wooden spacer, same length as chair (a yardstick works well) Crochet hooks (for detailing) -
Step 2: shuttles
You can start on any one of the four sides of the seat.
Tie your knot and slide it all the way to one corner
-- this is the starting point of your warp.
A "warp" is simply the first round of rope, pointing in one direction, that gives the weave its shape.You should have the majority of your rope at the other end of this knot.
Just keep it attached to the large ball of yarn/rope it came from.
Click here to learn how to tie a clove hitch below. , This spacer will keep some slack in the weave as you start in the first direction.
This will make it much, much easier to weave in the opposite side later.
If you make this first weave too tight you will have to remove it and start over. , Take your rope and lay it over the spacer, over the opposite seat pole, then back underneath everything to your starting point.
This is one loop.
You don't want to pull this as tight as possible.
It should be tight enough to hold its shape, but not so tight you can't lift it slightly with your fingers. , Starting with the pole you tied the knot on, lay the rope over the spacer, over the opposite pole, then back under everything to where you started.
Use your fingers to push the strings close together, then repeat until you have 5 total wraps. , Instead of wrapping across the whole width of the chair, wrap it the rope once around the pole opposite your starting side. , Come back to the beginning and wrap the rope just around this horizontal seat pole. , If you started on the left side of the seat, slide everything to the left.
You should have a total of 6 parallel strings on the seat posts:
The string wrapped for your clove hitch.
The five (5) strings woven across to the other side.
The string wrapped around the pole to create a spacer. , This process simply continues until you've finished one side of the chair.
To repeat:
Wrap the string across the width of the chair, going over the spacer, around the far pole, and back to where you started.
Repeat wrap for a total of five times.
Wrap around each pole individually to create a spacer.
Repeat., Don't try and tie a knot between two ends of the rope and keep going.
If you're running out of rope/yarn/etc, simply finish the set of 5 you are on and create your two spacers.
Tie the second spacer in, then create a clove hitch with a new strand of rope and "start over" from this point. , Once you get to the end of the seat pole, snip the rope so you have a 2-3" tail.
Use your crochet hooks to tuck this strand into your warp, preventing it from unraveling, then snip any excess string., Shuttles are simply thin yarn holders that you can slide into your weave, making it much easier to get a tight weave than forcing your hands through the warp.
Wrap up a small and a large shuttle, at minimum., Pick up the first five strings, and slide the spacer under it.
Then slide the spacer on top of the next five strings, alternating so that you have a ladder-like pattern. , This time, your job will be easy as every other set is already being held up by the other spacer.
To get a little extra width, turn the spacers so that their widest side points upwards. , You'll be starting perpendicular to your first set of weaves, but it doesn't matter which side you start on. , You're doing the same thing as before, just keeping the string between your first set of weaves.
This will help create the checkerboard pattern you're looking for. , Again, this is identical to the work from before
-- you create another spacer on each side of the chair every five times you wrap around the width. , You should already see how the weave is forming small squares.
As you work, you'll likely need to switch to smaller and smaller shuttles in order to fit under the weave, and you may have to switch to using just the thinner, 1/2" spacer or yardstick instead of both at once.
If you run out or rope, don't worry about tying another knot.
Simply , This takes time, but the precision is necessary for the final bits of the weave.
Simply pull the rope through, using the crochet hook to get into the center and pull the rope up and down every five strings., Once you've finished the weave, it should hold strongly on its own.
Your woven chair is done!, The weave goes perpendicular to the pole where you tie this knot., You should have a single strand of rope wrapped around your pole. , Make sure you do this loosely, so you could still get underneath the rope.
You'll still have the rope wrapped around the pole, with crisscrossing ropes on top. , Again, come under and around the pole. , Basically, you're making another crisscross of the ropes but, this time, you need to go under the line.
Note that this is under the second wrap you made, not the first one. , Hold onto the end of the rope, then pull hard on the rest of the line to tighten your knot. -
Step 3: spacers
-
Step 4: and a crochet hook
-
Step 5: from a local craft store.
-
Step 6: Tie the first half of your rope to one of the horizontal seat poles using a clove hitch.
-
Step 7: Lay the 1" spacer across the seat
-
Step 8: perpendicular to your knot.
-
Step 9: Wrap the rope around the whole width of the chair
-
Step 10: then back to your starting point.
-
Step 11: Keeping the strings from overlapping
-
Step 12: wrap the rope around everything four more times.
-
Step 13: After wrapping five times
-
Step 14: individually wrap the seat pole to create a spacer.
-
Step 15: Run the rope to the other side and wrap the first seat pole once to create a second spacer.
-
Step 16: Slide the strings close together
-
Step 17: making sure they don't crisscross.
-
Step 18: Repeat the process of five horizontal wraps and one spacer until you cover the whole chair.
-
Step 19: Tie a new clove hitch instead right after creating a spacer if you run out of rope and need to add more.
-
Step 20: Use a crochet hook to weave any stray strands back into the weave.
-
Step 21: Wrap the remainder of your rope onto your shuttles.
-
Step 22: Work your large spacer into warp
-
Step 23: passing it over every other group of five strings.
-
Step 24: Turn the seat upside-down and repeat the step above with your other spacer
-
Step 25: lifting the other sets of five strings.
-
Step 26: Starting with the rope on the larger shuttle
-
Step 27: tie the rope down to a seat pole with another clove hitch.
-
Step 28: Using the shuttle to slide under the lifted strings
-
Step 29: wrap the rope around the width of the chair five times.
-
Step 30: Wrap up the seat poles after five rounds to create spacers.
-
Step 31: Follow the same pattern as above -- five wraps
-
Step 32: one spacer -- by sliding the shuttle underneath the lifted strings.
-
Step 33: Use the crochet hook to manually weave the final few strands
-
Step 34: as the weave is likely too tight for the shuttles.
-
Step 35: Use scissors to clean up any loose threads
-
Step 36: strands
-
Step 37: and tails.
-
Step 38: Lay the end of the rope over the top of your pole (the edge of the seat).
-
Step 39: Pull the end under the pole and wrap it back around.
-
Step 40: Cross the end of the rope over the standing line wrapped around the pole.
-
Step 41: Tuck the end back under the pole as if double wrapping it.
-
Step 42: Slide the end underneath the loop you just made.
-
Step 43: Pull tightly on both ends of the rope to tighten it.
Detailed Guide
The materials needed are light and easy, though you may have some questions about how much you actually need:
About 2lbs of rope chord, cut into two roughly even halves (roughly 200 ft) 2-3 completely flat, 1/8" thick weaving shuttles, (various lengths) 1" thick wooden spacer, same length as chair 1/2" thick wooden spacer, same length as chair Very thin wooden spacer, same length as chair (a yardstick works well) Crochet hooks (for detailing)
You can start on any one of the four sides of the seat.
Tie your knot and slide it all the way to one corner
-- this is the starting point of your warp.
A "warp" is simply the first round of rope, pointing in one direction, that gives the weave its shape.You should have the majority of your rope at the other end of this knot.
Just keep it attached to the large ball of yarn/rope it came from.
Click here to learn how to tie a clove hitch below. , This spacer will keep some slack in the weave as you start in the first direction.
This will make it much, much easier to weave in the opposite side later.
If you make this first weave too tight you will have to remove it and start over. , Take your rope and lay it over the spacer, over the opposite seat pole, then back underneath everything to your starting point.
This is one loop.
You don't want to pull this as tight as possible.
It should be tight enough to hold its shape, but not so tight you can't lift it slightly with your fingers. , Starting with the pole you tied the knot on, lay the rope over the spacer, over the opposite pole, then back under everything to where you started.
Use your fingers to push the strings close together, then repeat until you have 5 total wraps. , Instead of wrapping across the whole width of the chair, wrap it the rope once around the pole opposite your starting side. , Come back to the beginning and wrap the rope just around this horizontal seat pole. , If you started on the left side of the seat, slide everything to the left.
You should have a total of 6 parallel strings on the seat posts:
The string wrapped for your clove hitch.
The five (5) strings woven across to the other side.
The string wrapped around the pole to create a spacer. , This process simply continues until you've finished one side of the chair.
To repeat:
Wrap the string across the width of the chair, going over the spacer, around the far pole, and back to where you started.
Repeat wrap for a total of five times.
Wrap around each pole individually to create a spacer.
Repeat., Don't try and tie a knot between two ends of the rope and keep going.
If you're running out of rope/yarn/etc, simply finish the set of 5 you are on and create your two spacers.
Tie the second spacer in, then create a clove hitch with a new strand of rope and "start over" from this point. , Once you get to the end of the seat pole, snip the rope so you have a 2-3" tail.
Use your crochet hooks to tuck this strand into your warp, preventing it from unraveling, then snip any excess string., Shuttles are simply thin yarn holders that you can slide into your weave, making it much easier to get a tight weave than forcing your hands through the warp.
Wrap up a small and a large shuttle, at minimum., Pick up the first five strings, and slide the spacer under it.
Then slide the spacer on top of the next five strings, alternating so that you have a ladder-like pattern. , This time, your job will be easy as every other set is already being held up by the other spacer.
To get a little extra width, turn the spacers so that their widest side points upwards. , You'll be starting perpendicular to your first set of weaves, but it doesn't matter which side you start on. , You're doing the same thing as before, just keeping the string between your first set of weaves.
This will help create the checkerboard pattern you're looking for. , Again, this is identical to the work from before
-- you create another spacer on each side of the chair every five times you wrap around the width. , You should already see how the weave is forming small squares.
As you work, you'll likely need to switch to smaller and smaller shuttles in order to fit under the weave, and you may have to switch to using just the thinner, 1/2" spacer or yardstick instead of both at once.
If you run out or rope, don't worry about tying another knot.
Simply , This takes time, but the precision is necessary for the final bits of the weave.
Simply pull the rope through, using the crochet hook to get into the center and pull the rope up and down every five strings., Once you've finished the weave, it should hold strongly on its own.
Your woven chair is done!, The weave goes perpendicular to the pole where you tie this knot., You should have a single strand of rope wrapped around your pole. , Make sure you do this loosely, so you could still get underneath the rope.
You'll still have the rope wrapped around the pole, with crisscrossing ropes on top. , Again, come under and around the pole. , Basically, you're making another crisscross of the ropes but, this time, you need to go under the line.
Note that this is under the second wrap you made, not the first one. , Hold onto the end of the rope, then pull hard on the rest of the line to tighten your knot.
About the Author
Andrea Morales
Enthusiastic about teaching crafts techniques through clear, step-by-step guides.
Rate This Guide
How helpful was this guide? Click to rate: