How to Prevent Microphone Feedback
Place the microphone behind the main speakers and in front of the monitors., Do not cup the microphone., Utilize a feedback eliminator., Use a graphic equalizer., Utilize the parametric equalizer on the channel strip., Treat the acoustics of the...
Step-by-Step Guide
-
Step 1: Place the microphone behind the main speakers and in front of the monitors.
If the monitors are too far off to the side of the mic, there can be feedback due to the pickup pattern of live vocal mics.
It's best to place the monitor directly behind the mic. -
Step 2: Do not cup the microphone.
Many singers have the tendency to place their hand around the microphone when performing which can cause unpleasant, high-pitched feedback.
Keep your hands at the back of the microphone.
If you are walking around on stage, be careful not to go past the main speakers or point the microphone at the monitors at all. , There are rack-mountable units that can be hooked up in the mains or monitor chain.
Feedback eliminators have the ability to detect when feedback is about to increase and cut the exact frequency, thus eliminating the feedback.
This can be very helpful if your act involves switching vocalists and moving the microphone around on stage. , A graphic equalizer allows a sound engineer to effectively prevent feedback from occurring during the performance
-- a process known as "ringing out" the microphones.
This is done before the show, during soundcheck.
During sound check, the vocalist sings through the microphone while the engineer increases the level slowly until feedback begins.
Once it starts, the engineer will find the correct band on the graphic equalizer and try to lower the gain.
This process should be done with every microphone during soundcheck.
On a high quality systems, there are usually 2 31-band graphic equalizers, 1 for the main mix and 1 for the monitor mix. , Most high-end mixing boards have a mid-sweep parametric equalizer that can help if you need to pull out a specific frequency.
The bandwidth of a parametric equalizer is often much smaller than the bandwidth on a graphic equalizer, and allows for precise frequency control.
Thus, it allows the engineer to pull out the frequency that's feeding back without compromising tone. , This is only applicable if the venue belongs to you.
Treating the acoustics can prevent excessive reverberation, which can potentially increase the chance of the mics feeding back.
Place foam above and on the back wall behind the stage to reduce stage volume.
Consequently the monitors won't have to be as loud, thus decreasing the chance for feedback to occur. -
Step 3: Utilize a feedback eliminator.
-
Step 4: Use a graphic equalizer.
-
Step 5: Utilize the parametric equalizer on the channel strip.
-
Step 6: Treat the acoustics of the room.
Detailed Guide
If the monitors are too far off to the side of the mic, there can be feedback due to the pickup pattern of live vocal mics.
It's best to place the monitor directly behind the mic.
Many singers have the tendency to place their hand around the microphone when performing which can cause unpleasant, high-pitched feedback.
Keep your hands at the back of the microphone.
If you are walking around on stage, be careful not to go past the main speakers or point the microphone at the monitors at all. , There are rack-mountable units that can be hooked up in the mains or monitor chain.
Feedback eliminators have the ability to detect when feedback is about to increase and cut the exact frequency, thus eliminating the feedback.
This can be very helpful if your act involves switching vocalists and moving the microphone around on stage. , A graphic equalizer allows a sound engineer to effectively prevent feedback from occurring during the performance
-- a process known as "ringing out" the microphones.
This is done before the show, during soundcheck.
During sound check, the vocalist sings through the microphone while the engineer increases the level slowly until feedback begins.
Once it starts, the engineer will find the correct band on the graphic equalizer and try to lower the gain.
This process should be done with every microphone during soundcheck.
On a high quality systems, there are usually 2 31-band graphic equalizers, 1 for the main mix and 1 for the monitor mix. , Most high-end mixing boards have a mid-sweep parametric equalizer that can help if you need to pull out a specific frequency.
The bandwidth of a parametric equalizer is often much smaller than the bandwidth on a graphic equalizer, and allows for precise frequency control.
Thus, it allows the engineer to pull out the frequency that's feeding back without compromising tone. , This is only applicable if the venue belongs to you.
Treating the acoustics can prevent excessive reverberation, which can potentially increase the chance of the mics feeding back.
Place foam above and on the back wall behind the stage to reduce stage volume.
Consequently the monitors won't have to be as loud, thus decreasing the chance for feedback to occur.
About the Author
Patricia Ross
Specializes in breaking down complex pet care topics into simple steps.
Rate This Guide
How helpful was this guide? Click to rate: