How to Make a Spiral‐Bound Book

Step-by-Step Guide

1. 1

   Step 1: Cut two pieces of cardboard down to the size you want.

   Use a metal ruler and a sharp craft blade to cut the cardboard.
   
   Thin cardboard from the back of a pad of paper or cereal box will work the best, but you can use chip board too.
   
   If you are using an old pad of paper, pull the back cover off and cut it in half.
2. 2

   Step 2: Cut some colorful paper to wrap the covers with.

   The paper needs to be 1-inch (2.54 centimeters) longer and wider than your cover.You can use any type of paper you want, such as scrapbooking paper, wrapping paper, or even construction paper.
   
   For a more unique look, create your design on the computer, then print it out on high-quality paper., You don't have to do this, especially if you used paper that's already fancy, like wrapping paper or scrapbooking paper.
   
   If you used construction paper or printer paper, consider drawing designs onto it, then coloring them in.
   
   Make the front cover fancier than the back cover.
   
   Add a title or an image. , Turn the paper so that the blank side is facing you.
   
   Brush a thin layer of liquid glue (ie:
   Mod Podge, tacky glue, or white school glue) onto the cardboard.
   
   Place the cardboard, glue-side-down, onto the paper.
   
   Make sure that it is centered.
   
   You can also use a glue stick instead.
   
   Smooth the paper down, if needed, with a ruler or credit card.
   
   Work your way from the middle of the cover to the outside. , Use a metal ruler and a craft blade to cut the corners of the paper off.
   
   Make sure that you cut all the way down to the cardboard.
   
   This will help remove bulk and help the paper lay smoother., Turn the cardboard so that the blank side is facing you, and the covered side is facing down.
   
   Coat the back of the paper with more glue.
   
   Fold it tightly over the edge of the cardboard, and press it down.
   
   Smooth the edges of the paper down, if needed.
   
   Work your way from the edges of the cover inward.
   
   Wipe away any glue that seeps out. , Cut two sheets of paper that are ½ inch (1.27 centimeters) than your cover, both lengthwise and widthwise.
   
   Try solid-colored paper if your cover is fancy, and patterned paper if your cover is plain., Turn the cover so that the paper side is facing down.
   
   Coat your cut paper with glue, then press it down onto the cover.
   
   This will cover up the bare cardboard and overlap part of the wrapped edges.Smooth the paper down, as before, then wipe off any excess glue. , Choose a waterproof decoupage glue, topcoat, or acrylic spray sealer.
   
   Spray it onto the front and back cover.
   
   Let the sealer dry before moving on.Be careful if you decorated or printed the paper; the ink may run. , You can use lined paper, printer paper, or even sketchbook paper.
   
   Avoid cutting more paper than this, especially if you are using thick sketchbook paper.
   
   If you cut more paper, you will need to make a bigger coil, which is more likely to warp out of shape.If you are using an old notebook, cut the paper in half, and use that instead., Take one of the pieces of paper you just cut.
   
   Orient it in the direction you want the cover to go.
   
   Use a pencil and ruler to draw a vertical line down the paper, about 2 millimeters from the left side edge.You can put the binding along the top edge instead.
   
   In this case, draw a horizontal line 2 millimeters from the top edge. , The hole needs to be to the right of the line so that it's closer to the middle of the paper than the edge.
   
   You can make the hole with a thin nail, a 3-millimeter screw punch, or a 1/8-inch (3-millimeter) hole puncher.Don't use a regular hole puncher.
   
   It's too big.
   
   If you made a horizontal line, punch the hole below the line instead.
   
   You can find these tools in the scrapbooking section of an arts and crafts shop. , Work your way up and down from the middle hole.
   
   Try to space the holes as evenly as you can.
   
   Leave about 5 millimeters of space at the top and bottom of the paper., Place the template on top of 4 sheets of paper.
   
   Punch more holes into the stack, using the template as a guide., Lay your template on top of your front cover.
   
   Punch the holes, then lift the template away.
   
   Repeat this step for the back cover., Place the back cover face-down.
   
   Stack the paper on top.
   
   Place the front cover on top, face-up.
   
   At this point, you can also insert other items into your book, such as folders and sticker sheets., Tap the stack against the table first to make sure that everything is aligned, especially the holes.
   
   Place binder clips along the top, bottom, and right-side edge.If you are making a top-bound book, place the clips on the bottom and side edges instead. , Get some 16-gauge stringing wire; you can find it in the beading section of an arts and crafts shop.
   
   Wrap it around a thick pen.
   
   How many times you wrap the wire around the pen depends on how many holes you have.
   
   If you have 24 holes, wrap it 24 times.Trim off the excess wire with wire cutters.
   
   Every so often, squish the coils together so that they are nice and tight. , Gently stretch the wire until it is about the same length as your book.
   
   If you put the holes along the top of you book, then stretch the wire to match the width., Poke one end of your coiled wire into the first hole on your book.
   
   Twist the wire until it reaches the next hole.
   
   Push it through the hole, and twist it again.
   
   Keep twisting and threading the wire until it comes out the last hole., Use needle-nose pliers to pinch the end of the wire at one end of your book.
   
   Bend the wire inward, towards the coil.
   
   Repeat this step for the other side of the book with the other end of the wire., If you still have any wire sticking out past the second/second-to-last-coil, you will need to trim it off.
   
   Do this with a pair of wire cutters.
3. 3

   Step 3: Decorate the paper

4. 4

   Step 4: if desired.

5. 5

   Step 5: Glue the paper to the cardboard.

6. 6

   Step 6: Clip the corners of the paper.

7. 7

   Step 7: Glue the edges of the paper down to the inside of the cardboard.

8. 8

   Step 8: Cut paper for the inside covers.

9. 9

   Step 9: Glue the paper to the back of each cover.

10. 10

    Step 10: Consider sealing the front and back covers.

11. 11

    Step 11: Cut 20 to 40 sheets of paper down to same size as the covers.

12. 12

    Step 12: Create your punching guideline and template.

13. 13

    Step 13: Punch your first hole along the center of the line.

14. 14

    Step 14: Make more holes

15. 15

    Step 15: spacing them 2 millimeters apart.

16. 16

    Step 16: Punch holes into the rest of your sheets of paper.

17. 17

    Step 17: Create more holes in the front and back covers.

18. 18

    Step 18: Stack everything together.

19. 19

    Step 19: Use binder clips to hold everything together.

20. 20

    Step 20: Wrap thick wire around a pen.

21. 21

    Step 21: Slide the wire off of the pen.

22. 22

    Step 22: Twist the wire through the holes.

23. 23

    Step 23: Bend the ends of the wire inward.

24. 24

    Step 24: Trim the excess wire off

25. 25

    Step 25: if needed.

Detailed Guide

About the Author