How to Open an iPhone
Power down your iPhone., Remove the SIM card., Before opening the iPhone, make sure that you are properly grounded so that you don’t damage the components with a static charge., Remove the screws., Pry open the case., Detach the ribbon cables...
Step-by-Step Guide
-
Step 1: Power down your iPhone.
Before you open the case, make sure your iPhone is completely turned off.
Simply turning the screen off will not suffice.
Press and hold the Power button until the power slider appears.
Slide the slider with your finger and your phone will turn off after a few moments.
Opening the iPhone without shutting it down can cause the iPhone to completely malfunction. -
Step 2: Remove the SIM card.
To avoid damaging your SIM card during the disassembly, remove it first.
The method varies depending on your iPhone model, but generally you will need a paperclip to press the SIM release button. , You can ground yourself by touching exposed metal. , There are two tiny screws at the bottom of the iPhone that need to be removed before you can open the phone.
These screws are located on either side of the connection port.
The Original iPhone and 3GS need a Phillips #00 screwdriver to remove the screws.
The iPhone 4 through the iPhone 6 models require a pentalobe (five point) screwdriver.
The screws are very small, so be sure not to lose them after you have removed them from the iPhone. , Once the screws are removed, you can pry the case open using a small flathead screwdriver.
Insert the screwdriver directly above the connection port where you removed the screws.
Gently push until the screen pops out of the casing.
Alternatively, you can attach a large suction cup to the bottom of the screen and slowly pull it up until the screen separates from the casing.
This may cause less damage than trying to force a screwdriver into the casing.Open the case slowly.
The screen is attached to the phone components with several ribbon cables.
If you separate the screen too quickly, you may damage the cables. , There are three small ribbon cables located at the top of the iPhone that connect the screen to the iPhone motherboard.
In order to complete remove the screen, you will need to detach these cable.
You must remove two ribbon connectors first before you can access the third connector.
Be especially careful when removing these ribbons, as damaging them will render your iPhone useless. , Once you have removed the ribbons, you can set the screen assembly aside.
Be sure that you do not damage the screen while you are not using it. , If you need to access the motherboard, remove the screws around the metal plate.
Some screws may be covered by stickers.
Once you remove all the screws, you can lift out the motherboard from the case. , In older iPhones, the battery is glued to the back plate of the iPhone.
Use a small flathead and work your way around the battery, gently prying it off of the back plate.
Be very careful not to puncture the battery during removal.
Newer iPhones have removable batteries that you can lift directly out of the housing after your remove the screw holding it in place., When you are done with your repair work, you can reassemble the iPhone by reversing the steps above.
Make sure that all of your ribbon connections are plugged back in to the correct sockets. -
Step 3: Before opening the iPhone
-
Step 4: make sure that you are properly grounded so that you don’t damage the components with a static charge.
-
Step 5: Remove the screws.
-
Step 6: Pry open the case.
-
Step 7: Detach the ribbon cables.
-
Step 8: Remove the screen.
-
Step 9: Access the motherboard.
-
Step 10: Remove the battery.
-
Step 11: Reassemble the iPhone.
Detailed Guide
Before you open the case, make sure your iPhone is completely turned off.
Simply turning the screen off will not suffice.
Press and hold the Power button until the power slider appears.
Slide the slider with your finger and your phone will turn off after a few moments.
Opening the iPhone without shutting it down can cause the iPhone to completely malfunction.
To avoid damaging your SIM card during the disassembly, remove it first.
The method varies depending on your iPhone model, but generally you will need a paperclip to press the SIM release button. , You can ground yourself by touching exposed metal. , There are two tiny screws at the bottom of the iPhone that need to be removed before you can open the phone.
These screws are located on either side of the connection port.
The Original iPhone and 3GS need a Phillips #00 screwdriver to remove the screws.
The iPhone 4 through the iPhone 6 models require a pentalobe (five point) screwdriver.
The screws are very small, so be sure not to lose them after you have removed them from the iPhone. , Once the screws are removed, you can pry the case open using a small flathead screwdriver.
Insert the screwdriver directly above the connection port where you removed the screws.
Gently push until the screen pops out of the casing.
Alternatively, you can attach a large suction cup to the bottom of the screen and slowly pull it up until the screen separates from the casing.
This may cause less damage than trying to force a screwdriver into the casing.Open the case slowly.
The screen is attached to the phone components with several ribbon cables.
If you separate the screen too quickly, you may damage the cables. , There are three small ribbon cables located at the top of the iPhone that connect the screen to the iPhone motherboard.
In order to complete remove the screen, you will need to detach these cable.
You must remove two ribbon connectors first before you can access the third connector.
Be especially careful when removing these ribbons, as damaging them will render your iPhone useless. , Once you have removed the ribbons, you can set the screen assembly aside.
Be sure that you do not damage the screen while you are not using it. , If you need to access the motherboard, remove the screws around the metal plate.
Some screws may be covered by stickers.
Once you remove all the screws, you can lift out the motherboard from the case. , In older iPhones, the battery is glued to the back plate of the iPhone.
Use a small flathead and work your way around the battery, gently prying it off of the back plate.
Be very careful not to puncture the battery during removal.
Newer iPhones have removable batteries that you can lift directly out of the housing after your remove the screw holding it in place., When you are done with your repair work, you can reassemble the iPhone by reversing the steps above.
Make sure that all of your ribbon connections are plugged back in to the correct sockets.
About the Author
Paul Gibson
Writer and educator with a focus on practical DIY projects knowledge.
Rate This Guide
How helpful was this guide? Click to rate: